Meadow Point Marine

Meadow Point Marine Mobile boat repair, upgrade/installation, and fabrication. We specialize in sailboats, serving the S

Rivets, bulbs, sheaves, instruments... what needs to be done aloft on your boat?
06/08/2022

Rivets, bulbs, sheaves, instruments... what needs to be done aloft on your boat?

Team Raven and their Corsair 24 trimaran asked for a few upgrades. Here are a few before/after shots. We were able to ...
06/05/2022

Team Raven and their Corsair 24 trimaran asked for a few upgrades. Here are a few before/after shots. We were able to fully rewire the boat, add instrumentation, and have an aluminum arch fabricated for their new solar panel. They will have an additional flex panel they can deploy for a total of 200W feeding a LiFePo4 battery. Good luck Team Raven!

Access hatches to critical steering connections are vital. This boat had a leaking 8" plastic deck plate right beneath t...
10/08/2021

Access hatches to critical steering connections are vital. This boat had a leaking 8" plastic deck plate right beneath the helmsperson. We opted for a bronze replacement which is much more solid. We epoxy sealed the edges/holes as well.

We trust our cleats to hold our boats safe at their slips and moorings. They and their backing plates should be up for t...
10/06/2021

We trust our cleats to hold our boats safe at their slips and moorings. They and their backing plates should be up for the task. Deck penetrations here were drilled/filled with epoxy, new plates bedded with Sikaflex, and all cleats/hardware bedded with butyl tape.

G10 is light, strong, inert, and easy to work with, suitable for backing plates, engine beds, or keel-bolt washers.

Small leaks unresolved can lead to serious damage. Roughly 10sqft of deck on this Cruise-a-home required replacement due...
09/08/2021

Small leaks unresolved can lead to serious damage. Roughly 10sqft of deck on this Cruise-a-home required replacement due to to a few small cracks. This old boat got some new core and fiberglass and is looking sharp with some nonskid paint.

A little excitement for the crew of this Cal 22 on Lake Union. The previous owner had clamped the gudgeon bolts too tigh...
09/07/2021

A little excitement for the crew of this Cal 22 on Lake Union. The previous owner had clamped the gudgeon bolts too tightly and compromised the skin. Luckily, the rudder floated and we were able to salvage it. It needed alignment, beveling of the existing glass, several layers of fiberglass/epoxy, fairing, primer, paint, and anti-fouling. Now it's back in action.

Hose clamps without rolled edges can cut through hoses over time. This coolant hose leak had been worsening until it fai...
07/19/2021

Hose clamps without rolled edges can cut through hoses over time. This coolant hose leak had been worsening until it failed completely, you can see the red crystal buildup. The autopsy confirms several areas that wore through. This temporary repair should get the owner home until they can order a replacement with the correct hose clamps.

Replacing a rear main seal can be an intimidating task. Getting to the seal is the challenge. We'd be glad to help you...
07/17/2021

Replacing a rear main seal can be an intimidating task. Getting to the seal is the challenge. We'd be glad to help you replace yours!

A rising exhaust elbow can prevent you from flooding your engine with seawater. This engine had a standard elbow with no...
06/25/2021

A rising exhaust elbow can prevent you from flooding your engine with seawater. This engine had a standard elbow with no rise, you can see evidence of salt crystal build-up dangerously close to the exhaust valves. Solved with a custom 316L SS mixing elbow.

Here's a project from last year, a custom 316L windlass bracket. This keeps the motor inside the v-berth and out of the ...
03/31/2021

Here's a project from last year, a custom 316L windlass bracket. This keeps the motor inside the v-berth and out of the elements. The black covers are UHMW sealed with butyl tape. Please forgive the weld quality, the weld chemistry was correct but the operator was lacking 👨‍🏭

Float switches can foul up in blackwater holding tanks. This is my first experience with external sensors. So far so goo...
03/29/2021

Float switches can foul up in blackwater holding tanks. This is my first experience with external sensors. So far so good!

A fuel/water separator that you can't see inside of is essentially useless. makes great fuel filters, this one is moun...
03/02/2021

A fuel/water separator that you can't see inside of is essentially useless. makes great fuel filters, this one is mounted on a custom G10 fiberglass plate, leaving plenty of access for the engine and making filter changes a breeze.

Address

Seattle, WA

Opening Hours

Monday 9am - 5pm
Tuesday 9am - 5pm
Wednesday 9am - 5pm
Thursday 9am - 5pm
Friday 9am - 5pm

Website

Alerts

Be the first to know and let us send you an email when Meadow Point Marine posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Meadow Point Marine:

Shortcuts

Share

Category